-40%
Evinrude Lightning 1 L1 V6 Lower Unit 135 150 175 HP Rare 1.78 Ratio From
Evinrude Lightning 1 L1 V6 Lower Unit 135 150 175 HP Rare 1.78 Ratio From
Evinrude Lightning 1 L1 V6 Lower Unit 135 150 175 HP Rare 1.78 Ratio From
Evinrude Lightning 1 L1 V6 Lower Unit 135 150 175 HP Rare 1.78 Ratio From
Evinrude Lightning 1 L1 V6 Lower Unit 135 150 175 HP Rare 1.78 Ratio From
Evinrude Lightning 1 L1 V6 Lower Unit 135 150 175 HP Rare 1.78 Ratio From
Evinrude Lightning 1 L1 V6 Lower Unit 135 150 175 HP Rare 1.78 Ratio From

Evinrude Lightning 1 L1 V6 Lower Unit 135 150 175 HP Rare 1.78 Ratio From

$ 1847.47

Availability: 17 in stock
  • Condition: Watch the video that I provided a link to in the description.
  • Warranty: No Warranty
  • Stroke: 2-Stroke
  • Engine(HP): 135 150 175
  • Brand: Evinrude

    Description

    Lightning 1 Lower Unit With Custom Made In The USA 1.78 Gear Set
    The Tooth Count Is 14/25 On These Gears
    Manufactured And Heat Treated Right In Wisconsin
    Please
    Click Here
    To See The YouTube Video
    I Made Telling You About This Lower Unit
    To Give You All Some Understanding Look At The Calculations Below
    As One Goes Up In Pitch,One Must Reduce Diameter To Maintain RPM In Most Cases. Prop Science Is A Black Art ...A Pure Guessing Game At Best
    Most Lighter High Performing Hulls Will Have A Slip Of 8-12% When A Driver That Knows How To Trim And Setup "X Height" Is At The Wheel
    This Lower Should Only Be Used On Light And Inherently Fast Hulls
    Assuming Your Engine Reaches 5800 Full Throttle RPM The Following Math Applies.
    19P Prop
    59
    MPH@0%Slip
    53
    MPH@10% Slip
    20P Prop
    62
    MPH@0%Slip
    56
    MPH@10% Slip
    21P Prop
    65
    MPH@0%Slip
    58
    MPH@10% Slip
    22P Prop
    68
    MPH@0%Slip
    61
    MPH@10% Slip
    23P Prop
    71
    MPH@0%Slip
    64
    MPH@10% Slip
    24P Prop
    74
    MPH@0%Slip
    67
    MPH@10% Slip
    25P Prop
    77
    MPH@0%Slip
    69
    MPH@10% Slip
    26P Prop
    80
    MPH@0%Slip
    72
    MPH@10% Slip
    27P Prop
    83
    MPH@0%Slip
    75
    MPH@10% Slip
    Keep in mind, this lower has aftermarket non standard gears
    There are no returns on this for any reason.
    There are no warranties expressed or implied.
    Since I am not there doing the actual installation on your motor, since I am not there to inspect your control system, since I am not there filling it with lube to the proper level allowing air to evacuate the hollows of the propshaft carrier, or doing the actual shift shaft adjustments, since I have no idea if your shift linkage is binding or if salt water has caused the cables to bind internally, Since I have no idea the condition of your control box , since I have no idea if the weld on that stainless linkage bell crank is fractured (common problem known to 60 deg motors)...there IS NO WARRANTY ON ANY OF MY LOWER UNITS. NONE. ZERO.
    See Here What A Linkage Failure (Common Issue) Looks Like On Evinrude E Tec 60 Degree 135 150 175HP Motors
    YOUTUBE VIDEO
    This Is Just One More Reason I Do Not Place Warranty On A Lower Unit That I Personally Am Not Installing
    Linkage and proper adjustment is super critical on any lower unit that uses the push pull shaft bell crank system as EVINRUDE uses
    You agree that you are purchasing this lower unit with non standard ratio gears and assume all risk as to how it performs on your own boat.
    All Bearings Have Been Changed Out For Brand New Koyo USA Bearings,
    Resealed Using OEM Seals etc.
    RH Rotation -
    And Now The Best Part!
    1.78 Ratio USA Made Gears
    No Other Lightning Has Them
    This Lower Unit Is ONLY To Be Used On 135 150 175 HP 60 Degree Motors.
    NOTE
    NOT TO BE USED ON ANY BIG BLOCK 3.3 or 3.4L Motors!
    IE: 200 225 250 300HP
    Not To Be Used On Heavy Boats Over 1600LBS
    Shipping To Continental 48 States VIA Fed Ex Ground